| Reg RZR Wheel Bearings | |
|
|
Author | Message |
---|
zingo
Number of posts : 606 Age : 74 Location : Jacksonville Florida Registration date : 2009-09-08
| Subject: Reg RZR Wheel Bearings May 25th 2011, 1:13 pm | |
| Can anybody recommend wheel bearings. I've got 3900 miles on an 09 Reg RZR and I need wheel bearing for the second time on the rear. I put the first set on at about 2000 miles. Are there any after market bearings that will last longer?
Thanks, jim | |
|
| |
rayray Moderator
Number of posts : 6335 Age : 58 Location : statesville,nc Registration date : 2010-08-15
| Subject: Re: Reg RZR Wheel Bearings May 25th 2011, 1:41 pm | |
| Give James (wv hotrod rhino) a call...he is a dealer for Superatv....On Superatv's web site they are 19.95.....James may be able to save you a few bucks. | |
|
| |
rayray Moderator
Number of posts : 6335 Age : 58 Location : statesville,nc Registration date : 2010-08-15
| Subject: Re: Reg RZR Wheel Bearings May 25th 2011, 5:39 pm | |
| Moose bearings are definatly good bearings...I have never tried Superatv bearings but everything alse that I have used of theirs has been good. Just trying to pass on some info. | |
|
| |
bubba53 Moderator
Number of posts : 12045 Age : 70 Location : statesville,nc Registration date : 2009-08-29
| Subject: Re: Reg RZR Wheel Bearings May 25th 2011, 10:13 pm | |
| | |
|
| |
Finzup
Number of posts : 2037 Age : 75 Location : Kenna, WV Registration date : 2009-07-13
| Subject: Re: Reg RZR Wheel Bearings May 25th 2011, 11:04 pm | |
| - zingo wrote:
- Can anybody recommend wheel bearings. I've got 3900 miles on an 09 Reg RZR and I need wheel bearing for the
second time on the rear. I put the first set on at about 2000 miles. Are there any after market bearings that will last longer?
Thanks, jim I think they're Chinese, but make sure you're not fooled by loose bushings(very common). | |
|
| |
rayray Moderator
Number of posts : 6335 Age : 58 Location : statesville,nc Registration date : 2010-08-15
| Subject: Re: Reg RZR Wheel Bearings May 25th 2011, 11:07 pm | |
| No BIGGY...RAYRAY has luv for mean people too... | |
|
| |
Carolinarhino
Number of posts : 1712 Age : 53 Location : Statesville, N.C. Registration date : 2010-08-19
| Subject: Re: Reg RZR Wheel Bearings May 25th 2011, 11:58 pm | |
| - rayray wrote:
- No BIGGY...RAYRAY has luv for mean people too...
Jesus said I had to LOVE them he didn't say I had to like them!!!!! | |
|
| |
bubba53 Moderator
Number of posts : 12045 Age : 70 Location : statesville,nc Registration date : 2009-08-29
| |
| |
zingo
Number of posts : 606 Age : 74 Location : Jacksonville Florida Registration date : 2009-09-08
| Subject: Re: Reg RZR Wheel Bearings May 26th 2011, 1:32 pm | |
| I'll check the bushing. Thanks guys. | |
|
| |
zingo
Number of posts : 606 Age : 74 Location : Jacksonville Florida Registration date : 2009-09-08
| Subject: Re: Reg RZR Wheel Bearings June 4th 2011, 6:31 pm | |
| Found my problem. I jacked up the rear and left rear wheel would move about and 1" to 1 1/2" when I shake it from top to bottom. The right rear would only move less than a 1/4 of an inch. The lower outside a-arm bolt was broken off where it enters the back side of the a-arm. I got a bolt from the hardware store and now I got very little movement. I can get that little movement out with new bushings. I'll be ordering OEM bolts cause the one from the hardware store is somewhat smaller in diameter. I'll be ordering new bushings too to get the rest of the slight movement out. The bolt broke in WV a couple of weeks ago but I did not notice it then. I was lucky for I put 540 miles on it that week. | |
|
| |
zingo
Number of posts : 606 Age : 74 Location : Jacksonville Florida Registration date : 2009-09-08
| Subject: Re: Reg RZR Wheel Bearings June 18th 2011, 9:56 am | |
| I put new EBC brake pads on all 4 corners and A-arm bushings from SuperDaves on all 4 too. Replaced the broken bolt on left rear, then decided to replace all a-arm bolts after I broke one on the front putting it back on. It didn't take much. I also bought a nice Torque wrench (3/8) and got everything torqued properly according to the shop manual. Still waiting for the front bolts though. I also replace all the wheel studs on the right rear. The dealer screwed up a couple with the impact wrench it appeared. I'm gotta change the oil and will be riding at Ocala NF next weekend. | |
|
| |
Gadget
Number of posts : 1464 Location : Hillsboro, Ohio Registration date : 2009-05-07
| Subject: Re: Reg RZR Wheel Bearings June 18th 2011, 2:10 pm | |
| dont throw away your old bolts, carry 1 of each with you ask geterdun about that. | |
|
| |
Bobby D
Number of posts : 14579 Location : Blacksburg,Va Registration date : 2009-02-08
| |
| |
zingo
Number of posts : 606 Age : 74 Location : Jacksonville Florida Registration date : 2009-09-08
| Subject: Re: Reg RZR Wheel Bearings June 18th 2011, 9:27 pm | |
| - Gadget wrote:
- dont throw away your old bolts, carry 1 of each with you ask geterdun about that.
That's my plan. | |
|
| |
Sponsored content
| Subject: Re: Reg RZR Wheel Bearings | |
| |
|
| |
| Reg RZR Wheel Bearings | |
|