Odd brake wear

Ok was working on my RZR today putting in new Hub bushings( which did not look worn when I took them out but made a huge difference in movement in the hub) and decided to change brakes as I was in there ... all but the Right rear were well worn , but the right rear was maybe half worn , anyone run into this , I had not noticed any odd braking ( pulling ETC) ... The brakes were also worn more on one pad than the other any suggestion on how to fix this ?

My first thought is some of the calipers are hanging. May need to clean them

If it was a canned ham I'd say brakes only gotta work on the 3 wheels that pull but tone is prolly right sounds like some of the pistons may be froze

brake sticking had it happen to mine the other week take apart and clean in front 2 cups and 4 seals 2 seals in each cup side 1 cup in back 2 seals take air hose and blow in line side to push cup are cups out be sure not to put your hand over them may take alot of air pressure to push them out just depends on how much stuff is in the sides of them

punder wrote:

Ok was working on my RZR today putting in new Hub bushings( which did not look worn when I took them out but made a huge difference in movement in the hub) and decided to change brakes as I was in there ... all but the Right rear were well worn , but the right rear was maybe half worn , anyone run into this , I had not noticed any odd braking ( pulling ETC) ... The brakes were also worn more on one pad than the other any suggestion on how to fix this ?

Drew.....I bet the last owner didnt know what the hell he was doing when he put brake pads on it!!

punder wrote:

Ok was working on my RZR today putting in new Hub bushings( which did not look worn when I took them out but made a huge difference in movement in the hub) and decided to change brakes as I was in there ... all but the Right rear were well worn , but the right rear was maybe half worn , anyone run into this , I had not noticed any odd braking ( pulling ETC) ... The brakes were also worn more on one pad than the other any suggestion on how to fix this ?

Alot more weight on the left side.....

I would send it back on a warranty claim.

By the way can am has 4wd. Just FYI.

Steve K wrote:

punder wrote:

Ok was working on my RZR today putting in new Hub bushings( which did not look worn when I took them out but made a huge difference in movement in the hub) and decided to change brakes as I was in there ... all but the Right rear were well worn , but the right rear was maybe half worn , anyone run into this , I had not noticed any odd braking ( pulling ETC) ... The brakes were also worn more on one pad than the other any suggestion on how to fix this ?

Drew.....I bet the last owner didnt know what the hell he was doing when he put brake pads on it!!

Possible

GETERDUN wrote:

punder wrote:

Ok was working on my RZR today putting in new Hub bushings( which did not look worn when I took them out but made a huge difference in movement in the hub) and decided to change brakes as I was in there ... all but the Right rear were well worn , but the right rear was maybe half worn , anyone run into this , I had not noticed any odd braking ( pulling ETC) ... The brakes were also worn more on one pad than the other any suggestion on how to fix this ?

Alot more weight on the left side.....

I getto lean to the center so that should not be a issue

mason thomas wrote:

brake sticking had it happen to mine the other week take apart and clean in front 2 cups and 4 seals 2 seals in each cup side 1 cup in back 2 seals take air hose and blow in line side to push cup are cups out be sure not to put your hand over them may take alot of air pressure to push them out just depends on how much stuff is in the sides of them

I was thinking if it stuck then it would have burned the pad up , I never noticed any pulling or odd braking ( with 3 wheels braking it would have turned ) . I did have the pads stick but I left the EMP brake on in the trailer and the pads stuck to the disc , but have ridden it 100-200 miles since then .

punder wrote:

mason thomas wrote:

brake sticking had it happen to mine the other week take apart and clean in front 2 cups and 4 seals 2 seals in each cup side 1 cup in back 2 seals take air hose and blow in line side to push cup are cups out be sure not to put your hand over them may take alot of air pressure to push them out just depends on how much stuff is in the sides of them

I was thinking if it stuck then it would have burned the pad up , I never noticed any pulling or odd braking ( with 3 wheels braking it would have turned ) . I did have the pads stick but I left the EMP brake on in the trailer and the pads stuck to the disc , but have ridden it 100-200 miles since then .

there's a adjustment screw on the caliper....it might have not been set right when they were changed last....

TBONE21 wrote:

I would send it back on a warranty claim.

By the way can am has 4wd. Just FYI.

We all know canned hamms have four wheel drive....just not yours...Tbone...and don't forget...the Bubba Army has pictures...